Print Page - Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!

Title: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 09:40:42 AM

Hello So I have this nas and I Opened TFTP Boot and was able to get it started in EM Mode and I Was able to find in the updater application in Windows 10. But that is as far as I have goten It gives me this message
(https://i.imgur.com/849yXjh.png)
and the settings in the debug menu
(https://i.imgur.com/RQt1IZS.png)
Can anyone help me?

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: oxygen8 on March 09, 2018, 10:24:26 AM

after tftp the nas has missing dhcp

set your pc ip to 169.254.212.6 and start LSUpdater again

a perfect way is described on my german howto
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/anleitung-tftp-und-firmware-flashen-mit-bildern-t903.html

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 10:29:44 AM

Quote from: oxygen8 on March 09, 2018, 10:24:26 AM
after tftp the nas has missing dhcp

set your pc ip to 169.254.212.6 and start LSUpdater again

a perfect way is described on my german howto
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/anleitung-tftp-und-firmware-flashen-mit-bildern-t903.html

Ok but now I get this
(https://i.imgur.com/g1YLPus.png)

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: oxygen8 on March 09, 2018, 11:09:21 AM

maybe the drive is demaged
do you need date

translate
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/blaues-blinken-datenrettung-von-einer-durch-stromausfall-nicht-mehr-ansprechbaren-ls-chlv2-t1849.html

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 11:20:26 AM

Quote from: oxygen8 on March 09, 2018, 11:09:21 AM
maybe the drive is demaged
do you need date

translate
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/blaues-blinken-datenrettung-von-einer-durch-stromausfall-nicht-mehr-ansprechbaren-ls-chlv2-t1849.html

I know this drive works it shows up on my pc but I did change out the original drive because I think the PCB is bad
(https://i.imgur.com/IrRHC0A.png)

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: oxygen8 on March 09, 2018, 11:48:09 AM

you try to use a new drive
then you have to read about debug and rebuild partition table
point 9. from my howto

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 11:54:50 AM

Quote from: oxygen8 on March 09, 2018, 11:48:09 AM
you try to use a new drive
then you have to read about debug and rebuild partition table
point 9. from my howto

Same Problem with another drive I know works

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: oxygen8 on March 09, 2018, 12:18:22 PM

which debug optons do you use?

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 12:39:38 PM

Quote from: oxygen8 on March 09, 2018, 12:18:22 PM
which debug optons do you use?

Just the Rebuild Partition Table

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 12:58:36 PM

Quote from: TehepicHD on March 09, 2018, 12:39:38 PM
Quote from: oxygen8 on March 09, 2018, 12:18:22 PM
which debug optons do you use?

Just the Rebuild Partition Table

And I also just tried all of them and it didn't work

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: oxygen8 on March 09, 2018, 01:16:07 PM

post your lsupdater.ini

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 01:21:20 PM

Quote from: oxygen8 on March 09, 2018, 01:16:07 PM
post your lsupdater.ini

Code Select

[Application]
Title = BUFFALO LinkStation Series Updater Ver.1.74
WaitReboot = 480
WaitFormat = 500
WaitFileSend = 600
WaitDiscover = 120

[Target]
ProductID = 0x00000011
ProductID2 = 0x00000012
ProductID3 = 0x00000013
ProductID4 = 0x00000014
ProductID5 = 0x00003006
ProductID6 = 0x00003007
ProductID7 = 0x00000015
ProductID8 = 0x00000016
ProductID9 = 0x00003008
ProductID10 = 0x00004001
ProductID11 = 0x00000017
ProductID12 = 0x00000019
ProductID13 = 0x00000020
ProductID14 = 0x00003010
Name = LinkStation

[Flags]
VersionCheck = 1
NoFormatting = 1

[SpecialFlags]

Debug = 1

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: oxygen8 on March 09, 2018, 01:46:35 PM

QuoteNoFormatting = 1

must be
NoFormatting = 0

(my howto ...)

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 07:16:06 PM

Quote from: oxygen8 on March 09, 2018, 01:46:35 PM
QuoteNoFormatting = 1

must be
NoFormatting = 0

(my howto ...)

That Worked! Thanks for the help!

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 09, 2018, 09:42:22 PM

Quote from: TehepicHD on March 09, 2018, 07:16:06 PM
Quote from: oxygen8 on March 09, 2018, 01:46:35 PM
QuoteNoFormatting = 1

must be
NoFormatting = 0

(my howto ...)

That Worked! Thanks for the help!

Hey so you know how I said it worked but the button broke while flashing firmware so...

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: oxygen8 on March 10, 2018, 09:54:25 AM

replacement
http://de.farnell.com/c-k/kss231g-lfs/tastschalter-spst-smd-2-5n/dp/1437639

Title: Re: Buffalo NAS LS-CH2.0TL Blinking Red Light 6 Times and need help!
Post by: TehepicHD on March 11, 2018, 07:15:50 PM

Quote from: oxygen8 on March 10, 2018, 09:54:25 AM
replacement
http://de.farnell.com/c-k/kss231g-lfs/tastschalter-spst-smd-2-5n/dp/1437639

Ok thanks!

Buffalo Forums

Products => Storage => Topic started by: TehepicHD on March 09, 2018, 09:40:42 AM