TFTP MODE E06: Lost boot image

[Querdenker28]

Hi All

 

First of all i wann say that this site is really good. As a complete noob i got alot of information for my second Hand Nas.

 

My System: I got a HS-DHTGL/R5 Nas with a 2GB Hard Disk in it. Its a new Disk.The NAS is connected to a Router with a RJ45 Cable. I dont know what Firmware i got on it because i dont know what the guy who had it before did with it.

 

My WKS: I got a win 7 64bit System. The Workstation is connected to a Router by a RJ45 cable and has a IP.

 

What i did. I read the FAQ`s and tried to make the procedure like explained in that Thread on the first page. I tried to get in to that "EM Mode" like explained here.

 

http://forums.buffalotech.com/t5/Storage/FAQ-1-of-5-EM-Mode-boot-procedures-please-read-this/td-p/11008" target="_blank" rel="nofollow">http://forums.buffalotech.com/t5/Storage/FAQ-1-of-5-EM-Mode-boot-procedures-please-read-this/td-p/11008

 

I did anything like they say there. I get the message that tells me "System EM Booting" and i release the "INIT" Button.

 

Then  it comes the next Point that sais

 

"After 120 seconds the NAS Navigator should not only find the unit, but the LCD display should show a link status (i.e. IP address, Hard Disk space used, etc)"

In my case it dont wait 120 seconds. i get after a few seconds the message telling me "Lost boot Image".

 

What i am doing wrong ?

 

Thanks for the Help

[micro77]

hi

im using linkstation xhl pro .

i change new harddisk but  nas give to me  E06 error code . 

i tried  tftprecovery   LS_XL_1.0  from here ;

ftp://24.153.165.234/../../mnt/array1/share/nas-recovery/" target="_blank">ftp://24.153.165.234/../../mnt/array1/share/nas-recovery/

 

but tftp dont serve any file

how can i  fix this problem ?

 

http://oi52.tinypic.com/2wmpagp.jpg">

[Shonk]

Use this one

 

http://www.mediafire.com/file/1h16poq6rbkkmml/TFTP%20Boot%20Recovery%201.41.rar" target="_blank">http://www.mediafire.com/file/1h16poq6rbkkmml/TFTP%20Boot%20Recovery%201.41.rar

 

and update to 1.42 straight after

[micro77]

thank your advice .

i tried and its seems working

but firmware cant loading ....

when i reboot nas then same error message E06 ...

 

 

[Shonk]

You need to boot it with that file i gave you

then update the firmware to 1.42

[micro77]

hi

its working again now....

 

i tried older frimware then 1.42 .

 

when update with 1.42 frimware  nas return to life .... 

 

:smileyvery-happy:

 

thank you very very much  for your helping.

 

best regards

[65Ch3v3LL3]

Is there a TFTP boot file for a TS-EX4.0TL/R5? I'm currently stationed in Afghanistan and we have two of these Terastations without the original hard drives that we need to get going. Any help would be greatly appreciated. 

[ut2004]

Hi Paul,

I have managed to get this far using your instructions - Thanks.

 

I got stuck, you have mention: "Once the NasNavi utility "sees" the Buffalo, you can start the firmware update."

My problem begins here, how do I start the firmware update?

 

I upgraded HDDs to 4x500GB, unit model is: TS-H1.0TGL/R5,

 

Buffalo NAS Navigator (v1.20) can see the unit but thats abut it.  I tried to use Setup > Browser Managment but it does not display anything, I dont have anything installed on this XP SP3 machine, its a clean isntall.  This setup goes throug a small switch nothing on it exept for the unit and PC, I tried to use https just in case, but no go either.  On the Buffalo NAS Navigator when I press the button "I'm here" its asking me for Administrators password?  Im not sure what passwort to enter here - or if I need to.

 

Any help would be greatly apreciated.

Thanks,

[davo]

ut2004 wrote:

My problem begins here, how do I start the firmware update?

 

Download the 1.33 firmware (see link below) make sure the TS and the PC are on the same IP range, disabled your anti virus and firewall software and run the TSUpdater.exe file.

 

http://109.104.88.61/files/downloads/TS-HTGL_1.33_1.31.zip" target="_blank">http://109.104.88.61/files/downloads/TS-HTGL_1.33_1.31.zip

 

[ut2004]

Thanks for the quick reply.

 

here is what I got:  TS-HTGL that needs updating wasn't found

Should I edit the .inf in any way to poit it to correct direction?

 

I have TFTP Boot still open, thats what Buffalo booted form, and I have Buffalo NAS Navigator open (TFTP Boot Recovery TS-RHTGL-R5 1.30) - should I close them before running the TS-RTGL 1.33-1.31 ?

Unit and PC are on the same IP segment.  PC 192.168.11.1 Unit is on the defauld: 192.168.11.150  I can PING the 192.168.11.150 I have no AV, and my Windows FW is disabled and stoped.

 

any idea?   thanks,

[davo]

wait, if you have a TS_HTGL why are you using the TFTP image for a TS-RHTGL?

[ut2004]

that is a good question, ...  I have no idea.  What should I use if unit model is: TS-H1.0TGL/R5

 

I think I was reading here some ware that this is what I need to use, but it could be someone just like me (not knowing enough).

 

thanks,

[ut2004]

update:

 

It worked (TS-H1.0TGL/R5)
I changed the PC, used the TFTP Boot Recovery TS-HTGL-R5 1.20 (and waited for good 5 min) and than I used TS-HTGL_1.33_1.31

 

I came back to life, but its in JAPANESE :)   is there any way I can change it? or this is F/W dependent if yes - which firware is in english, if you know.

 

Thanks, a lot!

[ut2004]

I forgot to mention, when I run Buffalo NAS Navigator info  on it is as follows:

 

Firmware: 1.33

TS-H2.0TGL/R5

 

which firmware I can use that is in English, Thanks.

[realborat]

You don`t need to change FW, 

Try following these steps to change the device back to English:

1. Connect to the web configuration utility by entering the TeraStation's IP address in a web browser.
2. In the column of blue items on the left hand side, select the second link.
3. Under the first header are two text fields; enter or modify the text in the second.
4. Under the third header, the first entry is a radio selection with two options; select the one on the right.
5. Under the fourth header (with two menu/pulldown boxes beneath it), set both menu boxes to the second entry in the list (the second menu box should say cp437).
6. Click the button, and close and reopen the browser.