HS-DH2.0TGL new Disks Samsung 250GB EMEGENCY MODE NO ARRAY INFO

[dth]

Hi,

 

i have read all the information and try it with my configuration (FAQ 1-4).

 

no sucsess.

 

The TS is direct connectet with an crossover cable to my xp system.

Adress is 192.168.11.1 Network 255.255.255.0 the TS has 192.168.11.150 Ping works.

TFTP-Server works, files loadet up.

TFTPboot works.

DISKS (4) were formatet with:

 

sda1 Bootable Primary Linux 205MB
sda2 Primary Linux 500MB
sda5 Extented Linux/Swap 510MB
sda6 Extended Linux XXXXMB

 

mkfs.ext3 /dev/sda1
mkfs.xfs /dev/sda2
mkfs.xfs /dev/sda6
mkswap  /dev/sda5

 

the data:

 

initrd.buffalo /boot
uImage.buffalo /boot
tar zxvf /home/ubuntu/Desktop/tsp/hddrootfs.buffalo.updated

 

is into the directories.

 

The disk image was  copyd wit dd to the other 3 disks.

All Disks have the same data.

Wenn i try tu update the TS with TSUpdater (debug is set to 1 and the other stuff with changing the debugswitches) it do not work, the message is:

 

Failed to formating, (ACP_STATE_FAILIURE) update is abordet.

 

No mather what i try, (java -jar acp_commander.jar -t 192.168.11.150 –o) do not help.

 

[Edit] Removed Telnet discussion

 

Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
  DMA zone: 32768 pages, LIFO batch:7
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10 tftpboot=yes
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110464KB available (3128K code, 573K data, 112K init)
Calibrating delay loop... 498.07 BogoMIPS (lpj=2490368)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 14
Flash bankwidth 1, base ff800000, size 400000
BUFFALO TS_HTGL FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_TS_HTGL_R5

 Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c16f5e00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (0)
'eth0'
Core Driver (ERROR)  0 : Warning: Future revision ID 02 for Device 6042. Implementing latest workarounds
Core Driver (ERROR)  0 : disable pci conventional features when working in PCI-X. pciCommand original value:0x0107e371. new value: 0x0107e011.
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi2 : Marvell SCSI to SATA adapter
scsi3 : Marvell SCSI to SATA adapter
physmap flash device: 400000 at ff800000
CFI: Found no phys_mapped_flash device at location zero
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
phys_mapped_flash: Found an alias at 0x40000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x80000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0xc0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x100000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x140000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x180000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x1c0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x200000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x240000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x280000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x2c0000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x300000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x340000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x380000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x3c0000 for the chip at 0x0
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v2.3
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ehci_platform and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :   429.200 MB/sec
   8regs     :   329.600 MB/sec
   32regs    :   513.200 MB/sec
raid5: using function: 32regs (513.200 MB/sec)
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
UPSDRV (C) BUFFALO INC. V.1.00 installed.
BUFFALO UPS Recover Function Initialized.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
md: md0 stopped.
md: md1 stopped.
Freeing init memory: 112K
md: md0 stopped.
md: md1 stopped.
md: md0 stopped.
md: md1 stopped.
md: md0 stopped.
md: md1 stopped.
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
root@HS-DHTGL-EMED9:~# ARM926EJ-Sid(wb)

 

 

 

 

 

What can i do??

 

 

Best regards,

 

Dieter

 

[PCPiranha]

Heres more information on acp state failure:

 

http://forums.buffalotech.com/t5/Storage/ACP-State-Failure-After-trying-to-flash-Firmware-Now-locked-out/m-p/29749/highlight/true#M23387" target="_blank" rel="nofollow">http://forums.buffalotech.com/t5/Storage/ACP-State-Failure-After-trying-to-flash-Firmware-Now-locked-out/m-p/29749/highlight/true#M23387

 

 

Also please do not discuss telnet on these forums, there are other forums you can bring that information to.