Print Page - Can't set volumes?

Title: Can't set volumes?
Post by: dsmithwc04 on December 31, 2012, 09:31:40 AM

I am trying to setup the hard drives on my LS-WCL2BE.

When trying to create a folder it shows nothing in the hard drive volumes. I can't figure out how to set up/ map the hard drive volumes. I went to webacces/system/storage and it shows both hard drives but the format and check buttons are greyed out. Also, under system info it shows the following..... Storage: Not available.

Title: Re: Can't set volumes?
Post by: davo on January 02, 2013, 03:43:17 AM

post a screen shot of the system/storage/Array1 section. Does it show Array1(EDP)?

Title: Re: Can't set volumes?
Post by: dsmithwc04 on January 02, 2013, 08:37:27 AM

I haven't enabled the raid 1 edp. I want to use raid 0 so I get full 2TB

Title: Re: Can't set volumes?
Post by: davo on January 02, 2013, 09:14:36 AM

davo wrote:
post a screen shot of the system/storage/Array1 section.

Title: Re: Can't set volumes?
Post by: dsmithwc04 on January 02, 2013, 09:28:19 AM

http://s695.beta.photobucket.com/user/dsmithwc04/media/buffaloscreenshot_zpsa64011ce.png.html#/user/dsmithwc04/media/buffaloscreenshot_zpsa64011ce.png.html?&_suid=135714047413808807073108228072

Title: Re: Can't set volumes?
Post by: davo on January 02, 2013, 10:02:34 AM

OK so, follow FAQ 2 of 5 to do a full debug (including rebuild partition table) once you do this the unit will start flashing 6 times (e06) once it does this follow FAQ 3 of 5 to reload the boot image.

Title: Re: Can't set volumes?
Post by: dsmithwc04 on January 02, 2013, 03:04:34 PM

Okay, attempted faq 2 of 5 and checked all the check marks even "rebuild partition table" and "Delete user-config".

ini file looks like this:

[Application] Title = BUFFALO LinkStation Series Updater Ver.1.64

WaitReboot = 1200

WaitFormat = 600

WaitFileSend = 600

WaitDiscover = 120

[Target]

ProductID = 0x00003006

ProductID2 = 0x00003007

ProductID3 = 0x00000016

ProductID4 = 0x00003008

ProductID5 = 0x00004001

ProductID6 = 0x00000017

ProductID7 = 0x00000019

Name = LinkStation

[Flags]

VersionCheck = 0

[SpecialFlags]

Debug = 1

NoFormatting = 0

Once, completed dialog box stated unable to format properly.

NAS is currently in EM Mode.

I went ahead and attempted faq 3 of 5 but never could get it to communicate with the tftp boot recovery exe. Just kept saying it was "accepting requests..."

I did put the static IP to 192.168.11.1 like it said.

Title: Re: Can't set volumes?
Post by: dsmithwc04 on January 02, 2013, 07:30:05 PM

Still no luck...

Title: Re: Can't set volumes?
Post by: dsmithwc04 on January 05, 2013, 10:27:20 PM

Looks like this is going back to the store. If I can't even get it to work out of the box how can I hope to keep it working...

Buffalo Forums

Products => Storage => Topic started by: dsmithwc04 on December 31, 2012, 09:31:40 AM