Buffalo Forums
Products => Storage => : TehepicHD March 09, 2018, 09:40:42 AM
-
Hello So I have this nas and I Opened TFTP Boot and was able to get it started in EM Mode and I Was able to find in the updater application in Windows 10. But that is as far as I have goten It gives me this message
(https://i.imgur.com/849yXjh.png)
and the settings in the debug menu
(https://i.imgur.com/RQt1IZS.png)
Can anyone help me?
-
after tftp the nas has missing dhcp
set your pc ip to 169.254.212.6 and start LSUpdater again
a perfect way is described on my german howto
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/anleitung-tftp-und-firmware-flashen-mit-bildern-t903.html
-
after tftp the nas has missing dhcp
set your pc ip to 169.254.212.6 and start LSUpdater again
a perfect way is described on my german howto
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/anleitung-tftp-und-firmware-flashen-mit-bildern-t903.html
Ok but now I get this
(https://i.imgur.com/g1YLPus.png)
-
maybe the drive is demaged
do you need date
translate
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/blaues-blinken-datenrettung-von-einer-durch-stromausfall-nicht-mehr-ansprechbaren-ls-chlv2-t1849.html
-
maybe the drive is demaged
do you need date
translate
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/blaues-blinken-datenrettung-von-einer-durch-stromausfall-nicht-mehr-ansprechbaren-ls-chlv2-t1849.html
I know this drive works it shows up on my pc but I did change out the original drive because I think the PCB is bad
(https://i.imgur.com/IrRHC0A.png)
-
you try to use a new drive
then you have to read about debug and rebuild partition table
point 9. from my howto
-
you try to use a new drive
then you have to read about debug and rebuild partition table
point 9. from my howto
Same Problem with another drive I know works
-
which debug optons do you use?
-
which debug optons do you use?
Just the Rebuild Partition Table
-
which debug optons do you use?
Just the Rebuild Partition Table
And I also just tried all of them and it didn't work
-
post your lsupdater.ini
-
post your lsupdater.ini
[Application]
Title = BUFFALO LinkStation Series Updater Ver.1.74
WaitReboot = 480
WaitFormat = 500
WaitFileSend = 600
WaitDiscover = 120
[Target]
ProductID = 0x00000011
ProductID2 = 0x00000012
ProductID3 = 0x00000013
ProductID4 = 0x00000014
ProductID5 = 0x00003006
ProductID6 = 0x00003007
ProductID7 = 0x00000015
ProductID8 = 0x00000016
ProductID9 = 0x00003008
ProductID10 = 0x00004001
ProductID11 = 0x00000017
ProductID12 = 0x00000019
ProductID13 = 0x00000020
ProductID14 = 0x00003010
Name = LinkStation
[Flags]
VersionCheck = 1
NoFormatting = 1
[SpecialFlags]
Debug = 1
-
NoFormatting = 1
must be
NoFormatting = 0
(my howto ...)
-
NoFormatting = 1
must be
NoFormatting = 0
(my howto ...)
That Worked! Thanks for the help!
-
NoFormatting = 1
must be
NoFormatting = 0
(my howto ...)
That Worked! Thanks for the help!
Hey so you know how I said it worked but the button broke while flashing firmware so...
-
replacement
http://de.farnell.com/c-k/kss231g-lfs/tastschalter-spst-smd-2-5n/dp/1437639
-
replacement
http://de.farnell.com/c-k/kss231g-lfs/tastschalter-spst-smd-2-5n/dp/1437639
Ok thanks!