VERY slow disk checking.

[Metzen]

My Terastation has been running a disk check since January 17th!

 

How do I make it stop checking?  This is beyond ridiculous!

 

Name:

TS-RXLB90

Firmware version:

1.50

Size:

6TB

[Jotin]

Simply restart the unit. It should not be doing a disk check for a month.

[Metzen]

Can I restart it from the web interface or do I need to do so onsite?

 

This is the email I got that prompted me to run a disk check:

Activity Report

[TeraStationInformation]

TeraStationName: TS-RXLB90

Time: 2011/02/22 01:00:02

IP Address: 10.1.1.20

Setting Screen:

Running Time : 82 days, 15:34:54

 

[HDD Usage Status]

[DISK error status]

DISK1 1

DISK2 0

DISK3 0

DISK4 0

[Jotin]

You can easily restart it from the interface. Go to system and then maintenance and restart the terastation.

[Metzen]

I get this message that prevents that:

Checking/Formatting Disk....

All features are disabled until the disk is completely checked/formatted. Also, file sharing is not available.

 

Details

 

Progress: Progress

 

 

[Jotin]

Ah ok, I wasnt aware of that I'm sorry. Then yes, you will need to have someone on site restart the unit. 

[Metzen]

Well...  I waited until April 1st to restart the unit.  I restarted it and I could access the Terastation interface but the share wasn't working.  I could see the hard disks there and in their RAID-5 config, but file sharing wasn't working.  After ~10 minutes or so, it automatically put me back to the "Checking/Formatting" disks screen.

 

What a nuisance.  What's the next steps for fixing this thing?  It's been checking disks for months now and after rebooting it, it *still* goes back to that stupid screen.  I can't believe it doesn't even let me check the logs at this stage.

[Metzen]

Here's the log.  It stops working at "FSCK XFS"  I was working about the date, it was March 31st I rebooted it.

I was able to pull the log by going to this link:

http://10.1.1.20/static/log/linkstation.log

 

 

Mar 31 15:13:04 TS-RXLB90 u-boot: BUFFALO U-BOOT Start !!!  

““ ““ # u-boot:  ** LOADER ** 

““ ““ # u-boot:  ** BUFFALO BOARD: DB-MV78100-A-BP LE (CFG_ENV_ADDR=fff80000) 

““ ““ # u-boot: U-Boot 1.1.4 (Dec 17 2009 - 11:58:00) Marvell version: 3.3.5 

““ ““ # u-boot: Buffalo Version: 2.08-1.00 

““ ““ # u-boot: U-Boot code: 00600000 -> 0066FFF0  BSS: -> 00684D30 

““ ““ # u-boot: Soc: MV78100 A0 (DDR2) 

““ ““ # u-boot: CPU running @ 800Mhz L2 running @ 266Mhz 

““ ““ # u-boot: SysClock = 266Mhz , TClock = 166Mhz  

““ ““ # u-boot: DRAM CAS Latency = 5 tRP = 5 tRAS = 19 tRCD=5 

““ ““ # u-boot: DRAM CS[0] base 0x00000000   size 512MB  

““ ““ # u-boot: DRAM Total size 512MB  64bit width 

““ ““ # u-boot: [512kB@fff80000] Flash: 512 kB 

““ ““ # u-boot: Addresses 8M - 0M are saved for the U-Boot usage. 

““ ““ # u-boot: Mem malloc Initialization (8M - 7M): Done 

““ ““ # u-boot: NAND:512 MB 

““ ““ # u-boot: CPU 0: ARM926 (Rev 0) 

““ ““ # u-boot: Streaming enabled  

““ ““ # u-boot: Write allocate disabled 

““ ““ # u-boot: FPU initialized to Run Fast Mode. 

““ ““ # u-boot: enaDCPref <NULL> 

““ ““ # u-boot: enaICPref <NULL> 

““ ““ # u-boot: setL2CacheWT no 

““ ““ # u-boot: setL2Size256K no 

““ ““ # u-boot: disL2Ecc no 

““ ““ # u-boot: disL2Prefetch yes 

““ ““ # u-boot: disL2Cache no 

““ ““ # u-boot: env finished 

““ ““ # u-boot: USB 0: host mode 

““ ““ # u-boot: USB 1: host mode 

““ ““ # u-boot: USB 2: host mode 

““ ““ # u-boot: PCI 0: PCI Express Root Complex Interface 

““ ““ # u-boot: PEX interface detected Link X4 

““ ““ # u-boot: PEX 4: interface detected no Link. 

““ ““ # u-boot: Net:   egiga0 [PRIME], egiga1 

““ ““ # u-boot: buffalo_change_power_status > Read 0x5c(swpoff_uboot_passed) 

““ ““ # u-boot: buffalo_change_power_status > Writing 0x5c(swpoff_uboot_passed) 

““ ““ # u-boot: Skip to wake up disk0.(already waken up) 

““ ““ # u-boot: Skip to wake up disk1.(already waken up) 

““ ““ # u-boot: Skip to wake up disk2.(already waken up) 

““ ““ # u-boot: Skip to wake up disk3.(already waken up) 

““ ““ # u-boot: Marvell Serial ATA Adapter 

““ ““ # u-boot: Integrated Sata device found 

““ ““ # u-boot: Found adapter at bus 0, device 1 ... Scanning channels 

““ ““ # u-boot: [1 0 0]: Enable DMA mode 

““ ““ # u-boot:   Device 2 @ 1 0: 

““ ““ # u-boot: Model: SAMSUNG HD154UI                          Firm: 1AG01118 Ser#: ###       

““ ““ # u-boot:             Type: Hard Disk 

““ ““ # u-boot:             Supports 48-bit addressing 

““ ““ # u-boot:             Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512) 

““ ““ # u-boot: [1 1 0]: Enable DMA mode 

…

““ ““ # u-boot: MAC Address on eth0  : ###    

““ ““ # u-boot: Signature version    : 1.00 

““ ““ # u-boot: Signature MACAddress : ###    

““ ““ # u-boot: 2791504 bytes read 

““ ““ # u-boot:    Image Name:   Linux-2.6.31.8-mv78100 

““ ““ # u-boot:    Created:      2010-11-04   6:18:02 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed) 

““ ““ # u-boot:    Data Size:    2791440 Bytes =  2.7 MB 

““ ““ # u-boot:    Load Address: 00008000 

““ 15:13:05 # u-boot:    Entry Point:  00008000 

““ ““ # u-boot: 9263414 bytes read 

““ ““ # u-boot:    Image Name:   initrd 

““ ““ # u-boot:    Created:      2010-11-12   6:25:24 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed) 

““ ““ # u-boot:    Data Size:    9263350 Bytes =  8.8 MB 

““ ““ # u-boot:    Load Address: 00000000 

““ ““ # u-boot:    Entry Point:  00000000 

““ ““ # u-boot: Signature version    : 1.00 

““ ““ # u-boot: Signature MACAddress : ###    

““ ““ # u-boot: 2791504 bytes read 

““ ““ # u-boot:    Image Name:   Linux-2.6.31.8-mv78100 

““ ““ # u-boot:    Created:      2010-11-04   6:18:02 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed) 

““ ““ # u-boot:    Data Size:    2791440 Bytes =  2.7 MB 

““ ““ # u-boot:    Load Address: 00008000 

““ ““ # u-boot:    Entry Point:  00008000 

““ ““ # u-boot: 9263414 bytes read 

““ ““ # u-boot:    Image Name:   initrd 

““ ““ # u-boot:    Created:      2010-11-12   6:25:24 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed) 

““ ““ # u-boot:    Data Size:    9263350 Bytes =  8.8 MB 

““ ““ # u-boot:    Load Address: 00000000 

““ ““ # u-boot:    Entry Point:  00000000 

““ ““ # u-boot: Signature version    : 1.00 

““ ““ # u-boot: Signature MACAddress : 00:24:a5:25:db:90 

““ ““ # u-boot: 2791504 bytes read 

““ ““ # u-boot:    Image Name:   Linux-2.6.31.8-mv78100 

““ ““ # u-boot:    Created:      2010-11-04   6:18:02 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed) 

““ ““ # u-boot:    Data Size:    2791440 Bytes =  2.7 MB 

““ ““ # u-boot:    Load Address: 00008000 

““ ““ # u-boot:    Entry Point:  00008000 

““ ““ # u-boot: 9263414 bytes read 

““ ““ # u-boot:    Image Name:   initrd 

““ ““ # u-boot:    Created:      2010-11-12   6:25:24 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed) 

““ ““ # u-boot:    Data Size:    9263350 Bytes =  8.8 MB 

““ ““ # u-boot:    Load Address: 00000000 

““ ““ # u-boot:    Entry Point:  00000000 

““ ““ # u-boot: Signature version    : 1.00 

““ ““ # u-boot: Signature MACAddress : 00:24:a5:25:db:90 

““ ““ # u-boot: 2791504 bytes read 

““ ““ # u-boot:    Image Name:   Linux-2.6.31.8-mv78100 

““ ““ # u-boot:    Created:      2010-11-04   6:18:02 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed) 

““ ““ # u-boot:    Data Size:    2791440 Bytes =  2.7 MB 

““ ““ # u-boot:    Load Address: 00008000 

““ ““ # u-boot:    Entry Point:  00008000 

““ ““ # u-boot: 9263414 bytes read 

““ ““ # u-boot:    Image Name:   initrd 

““ ““ # u-boot:    Created:      2010-11-12   6:25:24 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed) 

““ ““ # u-boot:    Data Size:    9263350 Bytes =  8.8 MB 

““ ““ # u-boot:    Load Address: 00000000 

““ ““ # u-boot:    Entry Point:  00000000 

““ ““ # u-boot:  ***** Debug ***** 

““ ““ # u-boot: diskinfo[0].IsMyDisk = 1 

““ ““ # u-boot: diskinfo[0].uImage_date = 1288851482 

““ ““ # u-boot: diskinfo[0].initrd_date = 1289543124 

““ ““ # u-boot: diskinfo[1].IsMyDisk = 1 

““ ““ # u-boot: diskinfo[1].uImage_date = 1288851482 

““ ““ # u-boot: diskinfo[1].initrd_date = 1289543124 

““ ““ # u-boot: diskinfo[2].IsMyDisk = 1 

““ ““ # u-boot: diskinfo[2].uImage_date = 1288851482 

““ ““ # u-boot: diskinfo[2].initrd_date = 1289543124 

““ ““ # u-boot: diskinfo[3].IsMyDisk = 1 

““ ““ # u-boot: diskinfo[3].uImage_date = 1288851482 

““ ““ # u-boot: diskinfo[3].initrd_date = 1289543124 

““ ““ # u-boot: newest_fw_dev is updated to 2 

““ ““ # u-boot: Booting from Device 2  

““ ““ # u-boot: hit any key to switch tftp boot. 

““ ““ # u-boot: Hit any key to stop autoboot:  2 ^H^H^H 1 ^H^H^H 0  

““ ““ # u-boot: Hit any key to stop autoboot:  3 ^H^H^H 2 ^H^H^H 1 ^H^H^H 0  

““ ““ # u-boot: 2791504 bytes read 

““ ““ # u-boot: 9263414 bytes read 

““ ““ # u-boot: <<stop_sound>> 

““ ““ # u-boot: ## Booting image at 02000000 ... 

““ ““ # u-boot:    Image Name:   Linux-2.6.31.8-mv78100 

““ ““ # u-boot:    Created:      2010-11-04   6:18:02 UTC 

““ ““ # u-boot:    Image Type:   ARM Linux Kernel Image (uncompressed) 

““ ““ # u-boot:    Data Size:    2791440 Bytes =  2.7 MB 

““ ““ # u-boot:    Load Address: 00008000 

““ ““ # u-boot:    Entry Point:  00008000 

““ ““ # u-boot:    Verifying Checksum ... OK 

““ ““ # u-boot: OK 

““ ““ # u-boot: call do_bootm_linux 

““ ““ # u-boot: ## Loading Ramdisk Image at 00900000 ... 

““ ““ # u-boot:    Image Name:   initrd 

““ ““ # u-boot:    Created:      2010-11-12   6:25:24 UTC 

““ 15:13:06 # u-boot:    Image Type:   ARM Linux RAMDisk Image (gzip compressed) 

““ 15:13:06 # u-boot:    Data Size:    9263350 Bytes =  8.8 MB 

““ 15:13:06 # u-boot:    Load Address: 00000000 

““ 15:13:06 # u-boot:    Entry Point:  00000000 

““ 15:13:06 # u-boot:    Verifying Checksum ... OK 

““ 15:13:06 # linkstation: Started logchkd

““ 15:13:06 # linkstation: Started inetd

““ 15:13:06 # errormon[1705]: errormon-ver.2.00 started 

““ 15:13:06 # linkstation: Started errormon

““ 15:13:06 # linkstation: Started kernelmon

““ 15:13:07 # kernelmon: cmd=SATA 0 plugged

““ 15:13:08 # kernelmon: cmd=SATA 1 plugged

““ 15:13:09 # kernelmon: cmd=SATA 2 plugged

““ 15:13:10 # kernelmon: cmd=SATA 3 plugged

““ 15:13:12 # kernelmon: cmd=raidresync 1 1 1 0

““ 15:13:14 # kernelmon: cmd=lanact 0 full eth1

““ 15:13:14 # kernelmon: cmd=lanact 1000 full eth1

““ 15:13:15 # kernelmon: cmd=lanact 0 full eth0

““ 15:13:16 # kernelmon: cmd=lanact 1000 full eth0

““ 15:13:16 # kernelmon: cmd=lanact 0 full eth1

““ 15:13:17 # kernelmon: cmd=lanact 1000 full eth1

““ 15:13:17 # hdd_raid_syncspeed.sh: /dev/md2 (raid5) sync speed max is setted to 3000

““ 15:13:17 # linkstation: Skipping mount process, because file /etc/bootmount_fail_dev_md2 is exist!

““ 15:13:17 # last message repeated 3 times

““ 15:13:36 # linkstation: cron.sh : logrotate.status is fine.

““ 15:13:42 # twonky: Media Server script is begun. 

““ 15:13:42 # twonky: Media Server setting is off

““ 15:13:47 # splx_buffalo.sh: Service is setted to off

““ 15:13:47 # root: linkstation

““ 15:13:52 # hdd_raid_syncspeed.sh: /dev/md0 sync speed max is setted to 50000

““ 15:13:52 # hdd_raid_syncspeed.sh: /dev/md1 sync speed max is setted to 50000

““ 15:13:52 # hdd_raid_syncspeed.sh: /dev/md10 sync speed max is setted to 50000

““ 15:13:52 # hdd_raid_syncspeed.sh: /dev/md2 (raid5) sync speed max is setted to 30000

““ 15:14:09 # linkstation: #[miconapl.mcon_get_version] mcon_version=TS-RXL/WL Ver2.1

““ 15:14:26 # errormon[1705]: Information situation detected! RAID         I14ARRAY1 Checking

““ 15:14:31 # twonky: Media Server script is begun. 

““ 15:14:31 # twonky: stop Media Server

““ 15:14:34 # linkstation: cron.sh : logrotate.status is fine.

““ 15:14:42 # linkstation: DWARF : Killing all dwarves

““ 15:14:47 # FsckXFS: try to repair XFS....

““ 15:15:23 # kernelmon: cmd=micon_interrupts

““ 15:15:28 # kernelmon: cmd=micon_interrupts

““ 15:15:38 # linkstation: log saved to NAND(cron)

““ 15:36:02 # kernelmon: cmd=raidresync 1 0 0 0