Author Topic: Terastation HD-H1.0TGL/R5 - Firmware Update HDHTGL2_16  (Read 8779 times)

bbert1

  • Calf
  • *
  • Posts: 2
Terastation HD-H1.0TGL/R5 - Firmware Update HDHTGL2_16
« on: August 06, 2009, 01:35:02 PM »
   

I applied the above listed Firmware Update to my Terastation.  Although the Link/Act light is on I cannot access the Terastation.  When I browse for it through the client utility or Internet explorer cannot be found. The client utility reports the following: Host Name: HD-HTGL-EM; Work Group: blank; IP Address: 192.168.11.150; Subnet Mask: 255.255.255.0; Firmware: --.  I have also tried pinging it no luck.  Any suggestions?


Kameran

  • Big Bull
  • *****
  • Posts: 505
Re: Terastation HD-H1.0TGL/R5 - Firmware Update HDHTGL2_16
« Reply #1 on: August 06, 2009, 02:47:06 PM »

I would recommend doing another force firmware flash.  Looks like the device doesn't have the firmware on it.

 

http://www.buffalotech.com/support/getfile/HDHTGL2_16.zip

 

If it doesn' t take the firmware across the network, you can try connecting to the device directly with a cat5e or cat6 cable.  Also you would need to set a static ip of 192.168.11.5.  Once you get the firmware on the device it should be back up running.

 

 


bbert1

  • Calf
  • *
  • Posts: 2
Re: Terastation HD-H1.0TGL/R5 - Firmware Update HDHTGL2_16
« Reply #2 on: August 07, 2009, 01:03:46 PM »
   I did everything you suggested without any success. I keep getting a message that the Terastation cannot be located.  Any other suggestions.

JoshC

  • Big Bull
  • *****
  • Posts: 1110
Re: Terastation HD-H1.0TGL/R5 - Firmware Update HDHTGL2_16
« Reply #3 on: August 07, 2009, 02:24:31 PM »
Is there an lights blinking on the front of the unit in some kind of pattern?
Message Edited by JoshC on 08-07-2009 02:26 PM

thuongshoo

  • Calf
  • *
  • Posts: 2
Re: Terastation HD-H1.0TGL/R5 - Firmware Update HDHTGL2_16
« Reply #4 on: October 30, 2009, 03:50:57 PM »
   

Hi All!

 

I have just bought a old one. I have only board so I'm using the board with ATX power. There is not any HDD is attached toh board. I will buy at the fureture when I get more money :D

Now my board can not still boot.  NASnavigator could detect the board but now it can not longer. I don't know why. Now :

- if I press power button, ATX fan will only operate for 1 second , and then power loss.

- if I press INIT button and power button at the same time or release and then press again, ATX fan will run forever:D, mpc chip is quite hot but NASnavigator can not detect at all.

 

I connect board with ADSL router(D-Link). Computer NIC has 3 IPs: 192.168.0.5 , 192.168.1.3 , 192.168.11.1

I'm using windows XP SP3, English version.

Now is too late. Tomorow, I will make a cross cable. I intend to connect board directly with computer.


thuongshoo

  • Calf
  • *
  • Posts: 2
Re: Terastation HD-H1.0TGL/R5 - Firmware Update HDHTGL2_16
« Reply #5 on: October 31, 2009, 03:49:36 AM »
   

NASnavigator can not detect anything longer. Perhaps I have to jtag flash:smileysad: