Author Topic: Reinstalling to an out-of warranty NAS with blank drives  (Read 15246 times)

Tiderfish

  • Calf
  • *
  • Posts: 9
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #60 on: September 12, 2020, 05:06:11 pm »
AHA! Did some googleing, and came across another poor soul having a similar issue. His solution was to edit the LSUpdater.ini file and add a couple of flags. When I went in there, I noticed the listed devices were wrong, because I brought this INI with the working LSUpdater.exe from the other download. So I deleted the bad INI, and imported the good one from the correct firmware download. Then I added the same flags he did. At last it would find the device. However when pressing the button to update the firmware, it said something like no partition firmware update aborted. So I changed the noformat option to 0 and it started loading the firmware!... for about 5 minutes, then I got an error that the uImage.buffalo file was missing. So I copied that into the same dir, and it wouldn't resume. Now I the updater program is having problems finding the unit again.

Here are the flags I used
Edit LSUpdater.ini
[Flags]
VersionCheck = 0
NoFormatting = 1 (changed this to 0 to let it format the partitions)

[SpecialFlags]
Debug=1

1000001101000

  • Debian Wizard
  • Big Bull
  • *****
  • Posts: 829
  • There's no problem so bad you cannot make it worse
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #61 on: September 12, 2020, 07:35:24 pm »
Which debug options did you use?

Tiderfish

  • Calf
  • *
  • Posts: 9
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #62 on: September 12, 2020, 09:12:56 pm »
WE GOT IT WORKING!!!

I think part of my problem is my Intel Pro NIC on my laptop didn't like connecting and disconnecting to the nas and a switch all the time. So it was making the transition from TFTP on 192.168, to DHCP with the LSUpdater more of a challenge. My solution to this was to put in a small switch between the nas, and laptop, for the TFTP on 192.168, then plug in an uplink to it so the nas can get dhcp to be found on the network. This is of course with all the other steps in place like the modified INI file, and the commandeered lsupdater from another firmware.

Once it finally loaded, the web-gui page was all in Japanese! I was thinking I downloaded the wrong firmware. Luckily I was able to log in and change the default language.

Thanks again 1000001101000, or should I call you 'h'? I was looking for a challenge today, but I didn't think it would have gone THAT far!

PS. Now that I have it all configured I am playing around with adding it to my Active Directory, and running into some issues. Should I just start a new thread for that?

clippingxpert

  • Calf
  • *
  • Posts: 2
    • Clipping Xpert
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #63 on: September 23, 2020, 01:07:02 am »
Sweet. Blank drives is important, usually so is having enough drives

makenov

  • Calf
  • *
  • Posts: 3
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #64 on: October 13, 2020, 08:16:38 pm »
Hi everyone, I am having a hard time with the LS WXL/R1 nas box.

After a power outage, the box reboot and the function LED is just SOLID RED. There is no flashing light sequence, no blue light, just a solid red all the time, and the drives are not spinning. Luckily, the data is not damaged and I have backed up all the stuffs. I did go trhough all the instructions I found  this forum, but still feel hopeless. Some of the symptons are:

- The only light on is function LED - it is solid RED all the time, No flashing light, no other colors
- Pressing the function button does not change the state of the function LED - solid red all the time.
- Seem like the box is stuck when it try to boot. It is in halt state forever
- No drive spinning. I have tried with several blank working drives.
- Nas Navigator/ LS updater/ acp_commander cannot detect the box ( I did edit the .ini file to enable the debug mode )
- TFTP boot cannot detect the box too ( I did connect the box to my pc, 192.168.11.1, turn off firewall, extract the firmware,..... )
- The 2 PCBs are not damaged, no burnmarks, no magic smoke.

Anyone knows what I should do :(

1000001101000

  • Debian Wizard
  • Big Bull
  • *****
  • Posts: 829
  • There's no problem so bad you cannot make it worse
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #65 on: October 13, 2020, 10:05:31 pm »
I haven't looked to closely at the ls-wxl boot-loader but I assume it's similar to the others I've looked at.

On the devices I've looked at the bootrom appears to turn on the red led before starting the bootloader. The bootloader turns it back of early in the boot process around when it starts flashing the power led. If the bootloader fails to load the red led just stays on. I've actually confirmed this behavior by wiping the bootloader on an ls210 with an spi programmer.

So one possibility is that the bootloader got corrupted.

I've also heard of similar behavior when there is something wrong with the power supply, odd behavior happens if it can't provide enough power. You could try booting the device without drives and see if anything changes (most of the power goes to powering the drives).

makenov

  • Calf
  • *
  • Posts: 3
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #66 on: October 13, 2020, 10:29:48 pm »
Hi 1000001101000,

I followed your suggestion, I removed all the drives and power up the nas box for 20 minutes, but seem like the the box is still stuck with the solid red LED. I also tried with different 12v 4a/5a power adapters and nothing changes. Another symptons I forgot to list is that the fan is not running too.

May be, as you said, the bootloader is corrupted. On the PCB there is a 4 pins un-soldered connector near the NAND flash chip. What are software and hardware I need to make it work again?

here is the image of the board
https://www.smallnetbuilder.com/myincludes/image_page.php?/images/stories/nas/buffalo_linkstaduo/buffalo_linkstaduo_board.jpg

« Last Edit: October 13, 2020, 10:31:44 pm by makenov »

1000001101000

  • Debian Wizard
  • Big Bull
  • *****
  • Posts: 829
  • There's no problem so bad you cannot make it worse
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #67 on: October 13, 2020, 10:54:29 pm »
You could try re-flashing the chip with one of these:
https://www.amazon.com/dp/B07R5LPTYM

If the only problem is that the data on the chip got corrupted somehow that might fix it. I donít know what the odds are of that but itís something to try.

If you do decide to give it a try I can help with the procedure, Iíve done it several times testing other issues. Maybe if I get some time Iíll write up a wiki page about it.


makenov

  • Calf
  • *
  • Posts: 3
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #68 on: October 13, 2020, 11:18:10 pm »
Hi 1000001101000,

I decided to give it a try. I will find someone the flash chip programmer or I just buy one. It may take 1 or 2 weeks to have the programmer delivered to my location. I will reply on this thread when I have everything ready.

Thank you for fast replying. This thing has beaten up me so far

1000001101000

  • Debian Wizard
  • Big Bull
  • *****
  • Posts: 829
  • There's no problem so bad you cannot make it worse
Re: Reinstalling to an out-of warranty NAS with blank drives
« Reply #69 on: October 13, 2020, 11:24:54 pm »
I've been happy the programmer I bought (the one from the link). It's been pretty useful for how cheap it was.