Author Topic: Terastation III (XL/5R) boot problem  (Read 3163 times)

Doppler

  • Calf
  • *
  • Posts: 4
Terastation III (XL/5R) boot problem
« on: May 12, 2016, 10:15:31 AM »
Hello, I really need some help. Few days ago I bought Terastation III (XL/5R) without HDD's. I'm trying to access it but with no success. Long story short, I was able to get data from serial console and this is the output. In best case scenario it stuck on Scanning JFFS2 FS: .- part.

Code: [Select]
Checking DATA BUS
Checking ADDRESS BUS
BUFFALO U-BOOT Start !!!
 ** LOADER **
 ** BUFFALO BOARD: DB-MV78100-A-BP LE (CFG_ENV_ADDR=fff80000)


U-Boot 1.1.4 (Sep 29 2014 - 16:22:36) Marvell version: 3.3.5
Buffalo Version: 2.11-1.02

U-Boot code: 00600000 -> 0066FFF0  BSS: -> 00684D30

Soc: MV78100 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 166Mhz

DRAM CAS Latency = 5 tRP = 6 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 512MB
DRAM Total size 512MB  64bit width
[512kB@fff80000] Flash: 512 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB

CPU 0: ARM926 (Rev 0)

Streaming enabled
Write allocate disabled
FPU initialized to Run Fast Mode.
enaDCPref <NULL>
enaICPref <NULL>
setL2CacheWT no
setL2Size256K no
disL2Ecc no
disL2Prefetch yes
disL2Cache no
env finished


USB 0: host mode
USB 1: host mode
USB 2: host mode
PCI 0: PCI Express Root Complex Interface
PEX interface detected Link X4
PEX 4: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
buffalo_change_power_status > Read 0x5c(swpoff_uboot_passed)
buffalo_change_power_status > Writing 0x5c(swpoff_uboot_passed)

Marvell Serial ATA Adapter
Integrated Sata device found
Found adapter at bus 0, device 1 ... Scanning channels
[1 0 0]: Enable DMA mode
  Device 2 @ 1 0:
Model: TOSHIBA MK5055GSX                        Firm: FG001M   Ser#:            X9MFS4AMS
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
[1 1 0]: Enable DMA mode
  Device 3 @ 1 1:
Model: WDC WD360GD-00FNA0                       Firm: 35.06K35 Ser#: WD-WMAH9123448
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 35304.6 MB = 34.4 GB (72303840 x 512)

MAC Address on eth0  : 00:1d:73:ff:dc:bd

Signature version    : 0.00
Signature MACAddress :

   This is not my HDD!!!
   Anyway load images...
** Bad partition 1 **
serch_boot_drv (528)>No kernel_file 2
** Bad partition 1 **
serch_boot_drv (608)>No init_file 2

Signature version    : -795951053.-1904475972
Signature MACAddress :
                       ▒▒▒▒▒▒▒V

   This is not my HDD!!!
   Anyway load images...
** Bad partition 1 **
serch_boot_drv (528)>No kernel_file 3
** Bad partition 1 **
serch_boot_drv (608)>No init_file 3


** Something is wrong, because of dev_desc->blksz is 0!!!
disk2 is not found!


** Something is wrong, because of dev_desc->blksz is 0!!!
disk3 is not found!

 ***** Debug *****
diskinfo[0].IsMyDisk = 0
diskinfo[0].uImage_date = 0
diskinfo[0].initrd_date = 0
diskinfo[1].IsMyDisk = 0
diskinfo[1].uImage_date = 0
diskinfo[1].initrd_date = 0
diskinfo[2].IsMyDisk = 0
diskinfo[2].uImage_date = 0
diskinfo[2].initrd_date = 0
diskinfo[3].IsMyDisk = 0
diskinfo[3].uImage_date = 0
diskinfo[3].initrd_date = 0

All disks are don't have signature or not mine!

All MyDisks don't have FW!!!
Anyway, try to load from FW from not MyDisks.Lost all init_rd
Trying NAND boot
partition changed to nand0,0
### JFFS2 loading 'uImage.buffalo' to 0x2000000
Scanning JFFS2 FS: .-

davo

  • Really Big Bull
  • VIP
  • *
  • Posts: 6149
Re: Terastation III (XL/5R) boot problem
« Reply #1 on: May 12, 2016, 11:28:59 AM »
How many disks are in it at the moment? What errors are in the display?
PM me for TFTP / Boot Images / Recovery files  LSRecovery.exe file.
Having network issues? Drop me an email: info@interwebnetworks.com and we will get it fixed!

Doppler

  • Calf
  • *
  • Posts: 4
Re: Terastation III (XL/5R) boot problem
« Reply #2 on: May 12, 2016, 02:46:08 PM »
Hi davo, thank you for your fast reply. There are two disks at the moment

TOSHIBA MK5055GSX 500 GB (laptop disk)
WDC WD360GD-00FNA0 40GB

This is an error message:
No init file at HDD 2

davo

  • Really Big Bull
  • VIP
  • *
  • Posts: 6149
Re: Terastation III (XL/5R) boot problem
« Reply #3 on: May 18, 2016, 11:03:07 AM »
It will need 4 disks to successfully install anyways. PM me for more info.
PM me for TFTP / Boot Images / Recovery files  LSRecovery.exe file.
Having network issues? Drop me an email: info@interwebnetworks.com and we will get it fixed!

Doppler

  • Calf
  • *
  • Posts: 4
Re: Terastation III (XL/5R) boot problem
« Reply #4 on: May 24, 2016, 06:33:52 AM »
I installed 4 disks, now I have a different problem, almost after turning on my unit, display became red with message "System Error E00 MPU no response" What could it be??

davo

  • Really Big Bull
  • VIP
  • *
  • Posts: 6149
Re: Terastation III (XL/5R) boot problem
« Reply #5 on: May 24, 2016, 06:44:14 AM »
Looks like the main board is faulty tbh.
PM me for TFTP / Boot Images / Recovery files  LSRecovery.exe file.
Having network issues? Drop me an email: info@interwebnetworks.com and we will get it fixed!

Doppler

  • Calf
  • *
  • Posts: 4
Re: Terastation III (XL/5R) boot problem
« Reply #6 on: June 18, 2016, 05:04:20 PM »
Is there any way I can try to fix it? Any manual to diagnose problem, anything that can halp? :(