Recent Posts

Pages: [1] 2 3 ... 10

Storage / Fan speed of LS-WXL with Debian 12

« Last post by eugrus on April 16, 2024, 07:48:57 PM »

So I've installed Debian 12 onto LS-WXL. Regards to 1000001101000 for the install image.

The fan is just running full speed all the time. The air comes out cold.

The sensors output is not informative (in terms of temperature):

Code: [Select]

# sensors
gpio_fan-isa-0000
Adapter: ISA adapter
fan1:        5000 RPM  (min =    0 RPM, max = 5000 RPM)

sensors-detect finds no sensors

Code: [Select]

# /sbin/sensors-detect
# sensors-detect version 3.6.0
# DMI data unavailable, please consider installing dmidecode 2.7
# or later for better results.
# Kernel: 6.1.85 armv5tel
# Processor: Feroceon 88FR131 rev 1 (v5l)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): 
modprobe: FATAL: Module cpuid not found in directory /lib/modules/6.1.85
Failed to load module cpuid.
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 16h thermal sensors...                           No
AMD Family 17h thermal sensors...                           No
AMD Family 15h power sensors...                             No
AMD Family 16h power sensors...                             No
Hygon Family 18h thermal sensors...                         No
Intel digital thermal sensor...                             No
Intel AMB FB-DIMM thermal sensor...                         No
Intel 5500/5520/X58 thermal sensor...                       No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): 
Sorry, no supported PCI bus adapters found.

Sorry, no sensors were detected.
Either your system has no sensors, or they are not supported, or
they are connected to an I2C or SMBus adapter that is not
supported. If you find out what chips are on your board, check
https://hwmon.wiki.kernel.org/device_support_status for driver status.

Is there a way to activate the sensors or do I have to speed down the fans manually via fancontrol or something?

Or are there actually no sensors and the stock firmware just did speed down the fan after the boot?

Storage / External USB drive not showing up on LinkStation SoHo 720 NAS

« Last post by Hostirad on April 15, 2024, 10:29:04 AM »

One reason I bought a LinkStation SoHo 720 NAS is the USB port for attaching an external drive. I had been using a Western Digital Elements 2TB external drive (WDBAAU0025HBK-01) as a shared network drive, attached to the USB port of a Linksys EA7500 router. It is set up with Samba 3.0.37. When I upgraded my router to a Linksys LN1100, I needed a new way to connect the external drive to my network because the new router does not have a USB port. Because the LinkStation SoHo 720 NAS does have two USB ports, I figured that I could simply plug the WD external drive into the rear USB port of the Linkstation. But when I tried this, I could not see the drive when connecting to the LinkStation through the web interface, Storage - USB Drives. (The primary hard drives in the LinkStation show up just fine.) I tried shutting down the LinkStation and starting it again, and the USB drive is still not visible. I disconnected the USB drive and reconnected to my old router, and it shows up as a network drive just fine. The drive is also readable when plugged directly into my Windows 11 laptop. Any ideas on making the external drive visible/accessible?

Storage / Re: Reinstalling to an out-of warranty NAS with blank drives

« Last post by eugrus on April 12, 2024, 05:55:52 AM »

Is there a ready Debian image for LS-WXL that I could just dd onto a drive before I put it into the device (and then extend the partition)? (instead of going through installation)

Storage / LS220D502 - Folders Disappearing

« Last post by tekkie27 on April 10, 2024, 10:41:55 AM »

Hello. I recently started having trouble with my LS220D502. It is set up as an SMB file share for less than ten users in an office. All of whom are using Windows 10 or 11, and Office 365. They connect to the share as a lettered drive. All computers are workgroup, no local domain, and not connected to Azure AD. We access simple Office documents.

Yesterday a folder disappeared. When I try to create a folder with the same name Windows gives me the error "The action can't be completed because the folder or a file in it is open in another program."

If I try to create a folder with the same name in the web interface, I get the error "Unknown error has occurred.internal server error"

I created the folder with a slightly different name and copied the files over from a backup.

That's when I realized the backup recently started failing on 4/5/2024 with various assertions of "Structure needs cleaning (117)"

Today a second folder has gone missing with the same symptoms.

What should I do?

EDIT:
I forgot to mention, after hours yesterday I ran a RAID scan on the RAID array. It is a RAID1 Array with two 2TB drives, with a capacity of 2TB. We are only using 64GB, 3.46%.

Storage / Re: Buffalo TeraStation TS5400R Hard Drive Capacity Support

« Last post by mjrgroup on April 07, 2024, 04:23:24 PM »

Thanks for posting your experience, Hackmaxxx!

I got the TS51210R 12-bay 3U rackmount unit up and running. It has two DDR3 DIMM slots with only one 8GB module populated, so it was easy to replace with two identical Crucial 8GB ECC modules.

The main CPU has one heatsink, which I repasted, but there are two Aquantia 10GB chips that are non-heatsinked and get quite warm.

I was able to successfully install 12x 14TB drives with no problems and am running RAID 6. The syncing does take a while but not as long as on the TS5400R units.

One note, the unit, even with the latest version version of 5.80 cannot support some of the latest SSL certificates with over 2048-bit encryption. The web interface says accepted but them the UI becomes completely unreachable and unresponsive and you have to flash firmware from the web-based tool to reset everything, even the pin holding the reset button won't fix the SSL issue. So no more SSL access to the web interface.

The only other problem is, the onboard fans do not spin fast enough and the drives run hot. I wish you could control the fan speed from the settings, because I would totally opt to run them at 100% if possible.

Storage / Re: Mapping shares

« Last post by davo on April 05, 2024, 05:36:31 AM »

You're looking for help and yet you don't even say what NAS you have, let alone the error you're getting?! Okay..

Storage / Mapping shares

« Last post by raydoc on April 04, 2024, 03:11:02 PM »

I moved houses and am setting up my network again. I can see my NAS drives on NASNavi2 but it will not let me map folders. When I go in to admin console, I can see all the folders and nothing has changed. It just refuses to let me see my folders or map them.

Any help is appreciated.