Buffalo Forums
Products => Storage => : erikleaver April 17, 2018, 04:58:00 PM
-
Hi,
My Linkstation has gotten very slow over the past few months. I'm using it across my home network (4 devices). It's slow in returning directory lists and in logging into the device itself (takes several minutes and navigating menu items inside the admin interface is also very slow). Overall, it's mostly unusable at this point due to latency.
I recently upgraded the firmware to 1.74. Running RAID 1. Using 321 gb out of a 2 TB config with RAID 1. So it shouldn't be a capacity issue.
Hard reboots help but only for short periods of time.
Any suggestions?
Thanks,
Erik
-
DLNA on or off?
disks ok?
1. open ssh
2. check the cpu and ram usage with
top
example
Mem: 50148K used, 1876K free, 0K shrd, 3428K buff, 21272K cached
CPU: 0% usr 2% sys 0% nice 96% idle 0% io 0% irq 0% softirq
Load average: 0.15 0.03 0.01
PID PPID USER STAT VSZ %MEM %CPU COMMAND
13459 13456 root R 3364 6% 0% top
1484 1 root S 2820 5% 0% /bin/sh /usr/local/sbin/miconmon_exec
2166 1 root S 34492 66% 0% /opt/bin/transmission-daemon -g /mnt/
1457 1 root S 28244 54% 0% /usr/bin/python /usr/local/sbin/Buffa
1768 1766 root S 10400 20% 0% /usr/local/sbin/smbd -D
1766 1 root S 10268 20% 0% /usr/local/sbin/smbd -D
1769 1 root S 5940 11% 0% /usr/local/sbin/nmbd -D
1717 1 nobody S 4648 9% 0% proftpd: (accepting connections)
3. check the SMART values for both disks
http://forum.nas-hilfe.de/festplatten-und-ssd-laufwerke/pruefung-einer-festplatte-unter-linux-t1291.html
(maybe you use wd green with not fixed bug)
http://forum.nas-hilfe.de/festplatten-und-ssd-laufwerke/western-digital-in-einer-ls-xhl-load-cycle-count-t1435.html
-
Thanks for the guidance. I'm not running DNLA.
I just ran check disk. When that process completes, I don't get any type of report -- console just takes me to the "shared folders". I'll need to do some more digging to figure out the disk health. But there are no warnings in the console.
I'll do the setup for ssl tonight & see if I can get a top report.
-
use smartctl to read out the SMART values
smartctl -a /dev/sda
and
smartctl -a /dev/sdb
-
So I didn't get far enough with the troubleshooting but I know have a red blinking light. Three 1 sec blinks indicates a bad drive.
I see the FAQ notes: Replace the hard drive indicated by the red LED.
But how can I tell if drive 1 or drive 2 needs replacing? After pulling the front panel off, I don't see any additional LEDs.
-
under the hdds you have the transparent hook
this hook will light with a red led on the demaged drive
-
Maybe it's not my day but I don't see any lights under the tabs.
Here's what I see: https://www.youtube.com/watch?v=50q1u95Atbk&feature=youtu.be
-
use a dark room
-
Waited til the evening. Still no light. Maybe its burned out or just not on.
I have an enclosure. Can I just yank the drives and test each one using the enclosure? Assuming I should run smart on each one.
Thanks
-
open ssh
http://forum.nas-hilfe.de/buffalo-technology-nas-anleitungen/ssh-freischalten-mit-2-klicks-t2468.html
check the smart status
http://forum.nas-hilfe.de/festplatten-und-ssd-laufwerke/pruefung-einer-festplatte-unter-linux-t1291.html
sda = disk1 = left drive
sdb = disk2 = right drive
-
Here's the result from top without any real requests going to the device: http://prntscr.com/jekcoe
And here it is in the middle of moving 700mb of images from a ssd to the Buffalo:
http://prntscr.com/jekeog
-
Ok, finally figured out how to get the smart values.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.05.06 21:28:31 =~=~=~=~=~=~=~=~=~=~=~=
login as: root
root@192.168.1.5's password:
root@Family:~# smartctl -d marvell -a /dev/sda
smartctl version 5.37 [arm-none-linux-gnueabi] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST2000DM001-1CH164
Serial Number: W1E6EZQK
Firmware Version: CC27
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Not recognized. Minor revision code: 0x1f
Local Time is: Sun May 6 21:29:10 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 227) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 092 092 006 Pre-fail Always - 214504044
3 Spin_Up_Time 0x0003 098 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 179
5 Reallocated_Sector_Ct 0x0033 096 096 010 Pre-fail Always - 5080
7 Seek_Error_Rate 0x000f 085 060 030 Pre-fail Always - 353875942
9 Power_On_Hours 0x0032 061 061 000 Old_age Always - 34298
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 179
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Unknown_Attribute 0x0032 088 088 000 Old_age Always - 12
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 063 049 045 Old_age Always - 706805797
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 179
193 Load_Cycle_Count 0x0032 089 089 000 Old_age Always - 22676
194 Temperature_Celsius 0x0022 037 051 000 Old_age Always - 37 (Lifetime Min/Max 0/21)
197 Current_Pending_Sector 0x0012 093 024 000 Old_age Always - 1208
198 Offline_Uncorrectable 0x0010 093 024 000 Old_age Offline - 1208
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 169423574959608
241 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 2643997231
242 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 6048029332
SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 12 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:28.384 READ DMA EXT
35 00 08 a8 58 9f 40 00 00:02:28.384 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:24.716 READ DMA EXT
35 00 08 f0 e4 1e 40 00 00:02:24.716 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:21.041 READ DMA EXT
Error 11 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:24.716 READ DMA EXT
35 00 08 f0 e4 1e 40 00 00:02:24.716 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:21.041 READ DMA EXT
35 00 10 e0 e4 1e 40 00 00:02:21.041 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:17.373 READ DMA EXT
Error 10 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:21.041 READ DMA EXT
35 00 10 e0 e4 1e 40 00 00:02:21.041 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:17.373 READ DMA EXT
35 00 08 08 d8 4e 40 00 00:02:17.373 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:13.714 READ DMA EXT
Error 9 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:17.373 READ DMA EXT
35 00 08 08 d8 4e 40 00 00:02:17.373 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:13.714 READ DMA EXT
35 00 08 a8 58 9f 40 00 00:02:13.714 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:10.083 READ DMA EXT
Error 8 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:13.714 READ DMA EXT
35 00 08 a8 58 9f 40 00 00:02:13.714 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:10.083 READ DMA EXT
35 00 10 90 99 9e 40 00 00:02:10.080 WRITE DMA EXT
35 00 08 78 59 52 40 00 00:02:10.079 WRITE DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@Family:~# smartctl -d marvell -a /s dev/sdb
smartctl version 5.37 [arm-none-linux-gnueabi] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST2000DM001-1CH164
Serial Number: W1E6EZZK
Firmware Version: CC27
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Not recognized. Minor revision code: 0x1f
Local Time is: Sun May 6 21:30:00 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 226) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 120 099 006 Pre-fail Always - 238384256
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 179
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 62455345
9 Power_On_Hours 0x0032 061 061 000 Old_age Always - 34301
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 179
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 063 050 045 Old_age Always - 689897509
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 179
193 Load_Cycle_Count 0x0032 076 076 000 Old_age Always - 49239
194 Temperature_Celsius 0x0022 037 050 000 Old_age Always - 37 (Lifetime Min/Max 0/20)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 97813585233401
241 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 6520205755
242 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 2195898015
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@Family:~# exit
logout
-
I ran a long test as well. Looks like it's indicating a problem with Drive A. Can you confirm?
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.05.06 21:34:33 =~=~=~=~=~=~=~=~=~=~=~=
login as: root
root@192.168.1.5's password:
root@Family:~# smartctl -d marvell -t long /dev/sda
smartctl version 5.37 [arm-none-linux-gnueabi] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 227 minutes for test to complete.
Test will complete after Mon May 7 01:22:01 2018
Use smartctl -X to abort test.
root@Family:~# smartctl -d marvell -a /dev/sda
smartctl version 5.37 [arm-none-linux-gnueabi] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST2000DM001-1CH164
Serial Number: W1E6EZQK
Firmware Version: CC27
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Not recognized. Minor revision code: 0x1f
Local Time is: Mon May 7 07:39:42 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 227) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 092 092 006 Pre-fail Always - 214674476
3 Spin_Up_Time 0x0003 098 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 179
5 Reallocated_Sector_Ct 0x0033 096 096 010 Pre-fail Always - 5080
7 Seek_Error_Rate 0x000f 085 060 030 Pre-fail Always - 355184808
9 Power_On_Hours 0x0032 061 061 000 Old_age Always - 34308
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 179
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Unknown_Attribute 0x0032 088 088 000 Old_age Always - 12
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 064 049 045 Old_age Always - 706805796
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 179
193 Load_Cycle_Count 0x0032 089 089 000 Old_age Always - 22676
194 Temperature_Celsius 0x0022 036 051 000 Old_age Always - 36 (Lifetime Min/Max 0/21)
197 Current_Pending_Sector 0x0012 093 024 000 Old_age Always - 1208
198 Offline_Uncorrectable 0x0010 093 024 000 Old_age Offline - 1208
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 97096325694978
241 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 2644126549
242 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 6048040636
SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 12 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:28.384 READ DMA EXT
35 00 08 a8 58 9f 40 00 00:02:28.384 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:24.716 READ DMA EXT
35 00 08 f0 e4 1e 40 00 00:02:24.716 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:21.041 READ DMA EXT
Error 11 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:24.716 READ DMA EXT
35 00 08 f0 e4 1e 40 00 00:02:24.716 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:21.041 READ DMA EXT
35 00 10 e0 e4 1e 40 00 00:02:21.041 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:17.373 READ DMA EXT
Error 10 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:21.041 READ DMA EXT
35 00 10 e0 e4 1e 40 00 00:02:21.041 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:17.373 READ DMA EXT
35 00 08 08 d8 4e 40 00 00:02:17.373 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:13.714 READ DMA EXT
Error 9 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:17.373 READ DMA EXT
35 00 08 08 d8 4e 40 00 00:02:17.373 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:13.714 READ DMA EXT
35 00 08 a8 58 9f 40 00 00:02:13.714 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:10.083 READ DMA EXT
Error 8 occurred at disk power-on lifetime: 33839 hours (1409 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 ff ff ff 4f 00 00:02:13.714 READ DMA EXT
35 00 08 a8 58 9f 40 00 00:02:13.714 WRITE DMA EXT
25 00 01 ff ff ff 4f 00 00:02:10.083 READ DMA EXT
35 00 10 90 99 9e 40 00 00:02:10.080 WRITE DMA EXT
35 00 08 78 59 52 40 00 00:02:10.079 WRITE DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 34300 1952017424
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@Family:~# smartctl -d marvell -t on long /dev/sdb
smartctl version 5.37 [arm-none-linux-gnueabi] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION ===
Sending command: "Execute SMART Extended self-test routine immediately in off-line mode".
Drive command "Execute SMART Extended self-test routine immediately in off-line mode" successful.
Testing has begun.
Please wait 226 minutes for test to complete.
Test will complete after Mon May 7 11:31:25 2018
Use smartctl -X to abort test.
root@Family:~# smartctl -d marvell -a /dev/sdb
smartctl version 5.37 [arm-none-linux-gnueabi] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST2000DM001-1CH164
Serial Number: W1E6EZZK
Firmware Version: CC27
User Capacity: 2,000,398,934,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Not recognized. Minor revision code: 0x1f
Local Time is: Mon May 7 12:26:19 2018 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 226) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 120 099 006 Pre-fail Always - 241158264
3 Spin_Up_Time 0x0003 096 096 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 179
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 62485148
9 Power_On_Hours 0x0032 061 061 000 Old_age Always - 34316
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 179
183 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
184 Unknown_Attribute 0x0032 100 100 099 Old_age Always - 0
187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0
190 Temperature_Celsius 0x0022 065 050 045 Old_age Always - 689897507
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 179
193 Load_Cycle_Count 0x0032 076 076 000 Old_age Always - 49239
194 Temperature_Celsius 0x0022 035 050 000 Old_age Always - 35 (Lifetime Min/Max 0/20)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 22527103501832
241 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 6520392768
242 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 2195986654
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 34315 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
root@Family:~# exit
logout
-
/dev/sda
197 Current_Pending_Sector 0x0012 093 024 000 Old_age Always - 1208
198 Offline_Uncorrectable 0x0010 093 024 000 Old_age Offline - 1208
-
Thanks. So that means disk 1 is bad & needs replacing. I then use the console to rebuild the raid right?
-
i recommend using the webif
and enable the E-Mail notification
-
alright. I'll give that a go.
Do I need to powercycle the unit to reset the red blinking error message or just ignore it if I go your suggested route?
-
without hotplug you have to shut down before removing the demaged drive